Kyocera Ai5555 Instruction Handbook Manual Download Page 146 | Manualshive

Page: 146 / 167

background image

Troubleshooting 6-7

Troubleshooting

Printer Basic Checklist

•

An error on your printer control panel may indicate a break in
communication from the network to the printer. This may be a
result of the network server going down, or from cables that are
loose or disconnected.

•

Check to see if the printer control panel displays printer status, and
be sure the printer is on-line. If the control panel displays an error,
check error conditions and jam conditions in the printer manual.

•

If the printer is plugged into the power outlet and the printer is
turned ON, try using another outlet.

•

If print jobs partially print, use the MAP browser to check parallel
port strobe size setting. If it is set to 1, change it to 5.

•

Make sure that all your connections are securely fastened.

•

Make sure the file server is up and on-line.

Network Connections to the NC-2

•

Make sure you are using the correct network interface port and that
each connection is secure.

•

Try another cable to make sure you do not have a bad cable.

«
...
144
145
146
147
148
...
»

Summary of Contents for Ai5555








































































































































































Reviews:

No comments

Related manuals for Ai5555

DELTAFLUX MT100

Brand: PIETRO FIORENTINI Pages: 16

Brand: Cansec Pages: 45

Brand: Cansec Pages: 43

Brand: Cansec Pages: 32

Brand: Ascon tecnologic Pages: 16

Brand: KIOUR Pages: 3

Brand: Topway Pages: 14

Brand: Wave Home Solutions Pages: 15

Brand: Trane Pages: 72

Brand: Apex Toys Pages: 7

Brand: Danfoss Pages: 16

Consolidated 2900-40 Series

Brand: Baker Hughes Pages: 80

Brand: Yoshitake Pages: 21

Brand: Oasis Pages: 7

Brand: Hanma Pages: 3

Brand: Unimig Pages: 4

Brand: Tate Pages: 32

TotalArc BMS 460346 SOLAR POWER

Brand: OGI Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands