Kyocera Ai5555 Instruction Handbook Manual Download Page 111

Page: 111 / 167

UNIX Printing Through TCP/IP 5-21

UNIX Printing Through TCP/IP

Configuring the IP Address on the NC-2 Print Server

Using BOOTP (continued)

The same information uses the following format on an RFC 951 system:

host

htype

haddr

iaddr

bootfile

printfast

00:40:af:03:af:6e

192.9.200.200

default boot

7. Start the BOOTP daemon by typing: bootpd -s

8. Check the printer to verify that the NC-2 Print Server is connected to the
network. Turn on the printer.

9. Wait until the printer powers up and finishes initializing to allow enough
time for the IP address to become known and to be saved in nonvolatile
memory. The NC-2 Print Server should re-initialize itself.

10. After the NC-2 Print Server has re-initialized, send a ping command to
verify that the print server obtained its IP address. For example:

ping 192.9.200.200

If the print server has the address, a confirmation message displays:

192.9.200.200 is alive

11. Remove your changes to the /etc/bootptab file.

12. Stop the BOOTP daemon and, if you want it to run, restart it.

Summary of Contents for Ai5555








































































































































































Search results

Summary of Contents for Ai5555

Reviews:

Related manuals for Ai5555

Brands by name

Popular brands

Kyocera Ai5555, Instruction Handbook Manual

Search results

Summary of Contents for Ai5555

Reviews:

Related manuals for Ai5555

Brands by name

Popular brands