Kyocera Ai5555 Instruction Handbook Manual Download Page 163 | Manualshive

Page: 163 / 167

background image

A-10

Jumper Settings

Changing Jumper Settings

Factory Default Jumper - JP10

The Reset to Factory Default JP10 jumper block allows you to force the
NC-2 back to factory default settings.

When you change this jumper, the parameters altered by any administrative
programs will be restored to factory default values, losing any special
configuration information that may have been entered.

The NC-2 is shipped with the jumper set to NORM for normal customer
configuration. To restore the NC-2 factory default setting, you must change
the jumper to FACT (for factory default), power up the NC-2, power down
the NC-2, and then change the jumper back to NORM.

See the following illustration.

BNC Connector

RXA

JP5

JP3

JP4

MAN AUTO 10BT THIN

NC-2 Board Illustration

JP10

NORM FACT

TXA

o o-o o-o o

o-o o

o o-o

«
...
161
162
163
164
165
...
»

Summary of Contents for Ai5555








































































































































































Reviews:

No comments

Related manuals for Ai5555

Brand: Samson Pages: 78

Brand: Rachio Pages: 16

C-NaviGator III

Brand: C-Nav Pages: 20

Brand: Daikin Pages: 38

Brand: Daikin Pages: 2

Brand: Daikin Pages: 148

Brand: Daikin Pages: 12

Brand: Daktronics Pages: 52

Brand: Waeco Pages: 20

Brand: Z-Wave Pages: 56

Brand: Gascat Pages: 32

Brand: Hanwell Pages: 34

Brand: HANSONG Pages: 11

Brand: Datapath Pages: 12

Brand: Hansen Pages: 4

Brand: Sanhua Pages: 3

SIGMA CONTROL 2

Brand: KAESER KOMPRESSOREN Pages: 246

Brand: Sanhua Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands