Kyocera Ai5555 Instruction Handbook Manual Download Page 14 | Manualshive

Page: 14 / 167

background image

NC-2 Introduction 1-5

NC-2 Introduction

Installation Requirements

Version of Protocol or NOS

q

Novell NetWare Version 2.15, 3.1x, or 4.x

q

UNIX/Windows/LAN Server systems supporting lpr over TCP/IP.

q

Macintosh System 7

q

DEC ULTRIX 4.3 or 4.4, DEC OSF/1 2.0 or 3.0, Solaris 1.1.3
or 2.3, (SUNOS 4.1.3 or 5.3), System V Release 4, HP-UX 9.01,
IBM AIX 3.2.5, or SCO UNIX 2 for our supporting TCP/IP

q

Banyan Vines

Software

q

Novell NetWare printing requires NetWare Capture, NPRINT or
PCONSOLE (later than 1.0) utilities.

q

The NC-2 Network Management Utility for Windows utility
requires Windows 3.1 or later; Windows for Workgroups 3.11;
Windows 95; or Windows NT 3.5 or later.

q

The Apple Administration program utility.

q

TCP/IP setup and maintenance requires the Network Management
Utility.

Hardware

q

Support for 10 megabit Ethernet networks: 10Base2 (also known
as ThinWire or Thinnet); and 10BaseT cables and hardware.

q

3 1/2" diskette drive on the workstation to accept Windows,
Macintosh or UNIX utilities.

«
...
12
13
14
15
16
...
»

Summary of Contents for Ai5555








































































































































































Reviews:

No comments

Related manuals for Ai5555

HomeTec Pro CFF3000

Brand: Abus Pages: 13

Brand: NAVITAS Pages: 7

Brand: Abus Pages: 2

Brand: Manfrotto Pages: 16

Brand: Samson Pages: 32

Brand: Quantum Pages: 15

Brand: LAS Pages: 6

Brand: YOKOGAWA Pages: 150

Brand: YOODA Pages: 3

Brand: YMGI Pages: 8

ArtNet-DMX Mux16

Brand: DMX4ALL Pages: 21

Brand: Olsen Pages: 4

Brand: Aqua Lung Pages: 24

Brand: SILENTRON Pages: 20

Brand: MacroAir Technologies Pages: 32

Brand: M-system Pages: 5

Brand: Satel Pages: 7

EAGLE CORE PLUS

Brand: PrimaLuceLab Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands