Kyocera Ai5555 Instruction Handbook Manual Download Page 131 | Manualshive

Page: 131 / 167

background image

UNIX Printing Through TCP/IP 5-41

UNIX Printing Through TCP/IP

Installing

TCP/IP

If Not Running lpd

Installing and Printing on HP/UX System (continued)

Using the SAM Program to Configure the Printer

HP supplies the sam program as an alternative method for configuring the
printer. The printer name must be the same as the one you entered during
the NC-2 Print Server installation.

When using sam, specify everything as if the printer were directly con-
nected to

/dev/

lprprinter/printer_name.

The software installed with your HP system can satisfy most of your
printing needs. HP supplies ASCII-to-PostScript filters, and the system will
invoke the filters automatically if you define the content type of the printer
as PostScript.

The HP/UX lp system also supplies interface scripts that produce PostScript
banners. Use the lpfilter command to define new filters and content types if
necessary.

The full power and flexibility of the lp print service is now available to you.
The fact that you are printing across the network is completely transparent.

«
...
129
130
131
132
133
...
»

Summary of Contents for Ai5555








































































































































































Reviews:

No comments

Related manuals for Ai5555

ACS850-04 series

Brand: ABB Pages: 296

Brand: ABB Pages: 320

Brand: ABB Pages: 50

Brand: ABB Pages: 56

Brand: VAT Pages: 29

Brand: Balboa Instruments Pages: 19

7000-2 - Escalade RAID Controller

Brand: 3Ware Pages: 2

Origami 4M-006-01

Brand: 4 Moms Pages: 28

Brand: H3C Pages: 69

Brand: JANE Pages: 144

Brand: M-Audio Pages: 26

Brand: M Climate Pages: 12

Brand: Comparato Pages: 20

Brand: DSC Pages: 16

Brand: Leggett & Platt Pages: 20

Brand: Contemporary Research Pages: 22

Brand: Samson Pages: 36

Brand: CLIMAVENETA Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands