Kyocera Ai5555 Instruction Handbook Manual Download Page 21 | Manualshive

Page: 21 / 167

background image

2-6 Installation

Installation

Network Management Utility

Installation Procedure

This Windows based utility can be installed on any workstation hard drive
or network drive. It is recommended that you install the utility program onto
an area of the file server restricted to users with Supervisor/Administrator
rights; however this is not a requirement.

When you install the Network Management Utility diskette, the MAP
(Management Access Program) browser installs automatically.

1. Start Windows on your PC or workstation.

2. Insert the Network Management Utility diskette in drive A: or B:

3. In the Windows Program Manager, select File.

4. Select RUN from the menu.

5. At RUN, type A:\SETUP.EXE or B:\SETUP.EXE and click OK.

6. Read the information screen and click on Continue.

7. Identify a path for the program.

The path default is C:\MAP

You can change the path or use the default. The installation begins.

8. When installation is completed, remove the diskette from the disk drive.

To use the Network Management Utility, see information starting on p. 3-6.

«
...
19
20
21
22
23
...
»

Summary of Contents for Ai5555








































































































































































Reviews:

No comments

Related manuals for Ai5555

Evolution Series E9000

Brand: GE Pages: 44

PACSystems RX7i

Brand: GE Pages: 469

GuardSwitch 300 Series

Brand: GE Pages: 2

GuardSwitch 300 Series

Brand: GE Pages: 2

Masoneilan VariPak 28001

Brand: GE Pages: 24

Brand: Rain Bird Pages: 48

Brand: Hardi Pages: 2

Brand: YASKAWA Pages: 64

Brand: V2 Pages: 3

Brand: FrSky Pages: 2

Brand: Eaton Pages: 2

Brand: Eaton Pages: 2

Brand: Eaton Pages: 8

Brand: Jedia Pages: 12

Brand: JED Micro Pages: 10

Brand: JCM Technologies Pages: 2

Compact Comfort VAV12

Brand: SAI HVAC Pages: 16

Brand: Saitek Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands