Kyocera Ai5555 Instruction Handbook Manual Download Page 147 | Manualshive

Page: 147 / 167

background image

6-8 Troubleshooting

Troubleshooting

NC-2 Troubleshooting

Make sure you have properly configured the NC-2 for each network
protocol you are using, i.e., Novell, AppleTalk, and TCP/IP.

•

Enable all protocols you are using.

•

Use the Network Management Utility to enable the
protocols that you are using with NC-2.

Novell

•

For Novell, make sure you configure all NC-2 printers using
PCONSOLE. You need to configure each printer you want to use.

AppleTalk

•

For AppleTalk, make sure the NC-2 printer(s) are listed in
Chooser. This printer appears as the NC2#<Serial number> 1 in
Chooser (unless you changed it).

All Protocols

•

Check the NC-2 status page to make sure your network protocol
is enabled.

•

Check the NC-2 status page to make sure there is no error
message. If there is an error page, follow the instructions on the
page to make your corrections and then try printing again.

«
...
145
146
147
148
149
...
»

Summary of Contents for Ai5555








































































































































































Reviews:

No comments

Related manuals for Ai5555

Brand: CAME Pages: 12

Brand: CAME Pages: 16

Brand: Ultrak Pages: 41

Brand: Zander Aachen Pages: 10

Brand: CALEFFI Pages: 12

QuickSetter+ 132 Series

Brand: CALEFFI Pages: 5

Brand: Garmin Pages: 4

Brand: Hama Pages: 8

Brand: Lamtec Pages: 136

Brand: Mamas & Papas Pages: 24

Brand: Mamas & Papas Pages: 24

Brand: Sanhua Pages: 3

Brand: QED Pages: 26

Brand: Watts Pages: 4

Brand: WaterCop Pages: 4

Brand: cinetto Pages: 56

Brand: Data Signs Pages: 23

Brand: Nemesis Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands