Kyocera Ai5555 Instruction Handbook Manual Download Page 161 | Manualshive

Page: 161 / 167

background image

A-8

Jumper Settings

Changing Jumper Settings

Ethernet Interface Jumper - JP3

Change this jumper when using Thinnet Ethernet connections.

1. Locate the JP3 Jumper on the board (see illustration below).

2. Remove the jumper from the 10BT setting and place it on the THIN
setting, as shown. This jumper must be changed in connection with the
Media Selection Type jumper described on the previous page.

NOTE: After changing the jumper to the Thinnet connection, refer to the Installation
instructions in Section 2, Connect the Network to NC-2: Ethernet.

BNC Connector

RXA

JP5

JP3

JP4

MAN AUTO 10BT THIN

NC-2 Board Illustration

JP10

NORM FACT

TXA

o o-o o o-o

o-o o

o o-o

«
...
159
160
161
162
163
...
»

Summary of Contents for Ai5555








































































































































































Reviews:

No comments

Related manuals for Ai5555

Brand: K&K Pages: 6

Brand: FAAC Pages: 12

Brand: NEC Pages: 149

Brand: NEC Pages: 13

Minas A4 Series

Brand: Panasonic Pages: 5

Brand: Panasonic Pages: 15

Brand: Panasonic Pages: 42

Brand: Danfoss Pages: 37

Brand: Daikin Pages: 44

Brand: Jands Pages: 7

Brand: hager Pages: 11

coviva Smartbox TKP100A

Brand: hager Pages: 34

Brand: RadioMaster Pages: 49

SUPERREMOTE UR19A

Brand: X10 Pages: 3

Brand: Xantech Pages: 102

Brand: Xantech Pages: 17

Brand: X10 Pages: 2

Brand: Auber Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands