Keysight Technologies InfiniiVision 3000 X Series User Manual Download Page 241

Page: 241 / 432

Mask Testing

Keysight InfiniiVision 3000 X-Series Oscilloscopes User's Guide

241

To clear the mask and switch off mask testing, press the

Back/Up key to

return to the Mask Test Menu, then press the

Clear Mask

softkey.

If infinite persistence display mode (see

"To set or clear persistence"

on page 131)

is "on" when mask test is enabled, it stays on. If infinite persistence is "off" when

mask test is enabled, it is switched on when mask test is switched on, then infinite

persistence is switched off when mask test is switched off.

Troubleshooting

Mask Setup

If you press

Create Mask

and the mask appears to cover the entire screen, check the

± Y and ± X settings in the Automask Menu. If these are set to zero the resulting

mask will be extremely tight around the waveform.

If you press

Create Mask

and it appears that no mask was created, check the ± Y

and ± X settings. They may be set so large that the mask is not visible.

Mask Test Setup Options

From the Mask Test Menu, press the

Setup

softkey to enter the Mask Setup Menu.

Back

Summary of Contents for InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Search results

Summary of Contents for InfiniiVision 3000 X Series

Reviews:

Related manuals for InfiniiVision 3000 X Series

Brands by name

Popular brands

Keysight Technologies InfiniiVision 3000 X Series, User Manual

Search results

Summary of Contents for InfiniiVision 3000 X Series

Reviews:

Related manuals for InfiniiVision 3000 X Series

Brands by name

Popular brands