Keysight Technologies InfiniiVision 3000 X Series User Manual Download Page 28

Page: 28 / 432

Keysight InfiniiVision 3000 X-Series Oscilloscopes User's Guide

Getting Started

Install the Optional LAN/VGA or GPIB Module

If you need to install a DSOXLAN LAN/VGA module or a DSOXGPIB GPIB module,

perform this installation before you power on the oscilloscope.

If you need to remove a module before installing a different module, pinch the

module's spring tabs, and gently remove the module from the slot.

To install a module, slide the module into the slot on the back until it is fully

seated.

The module's spring tabs will latch into the slot, keeping the module in place.

Tilt the Oscilloscope for Easy Viewing

There are tabs under the oscilloscope's front feet that can be flipped out to tilt the

oscilloscope.

&%% LViihB6M

&%%"')%K!*%$+%=o

&%%"&'%K!*%$+%$)%%=o

L6GC>C</B6>CI6>C
<GDJC9ID 6KD>9
:A:8IG>8H=D8@

LAN/VGA Module

GPIB Module

Module Slot

NOTE

The LAN/VGA or GPIB module must be installed before powering on the oscilloscope.

Summary of Contents for InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Search results

Summary of Contents for InfiniiVision 3000 X Series

Reviews:

Related manuals for InfiniiVision 3000 X Series

Brands by name

Popular brands

Keysight Technologies InfiniiVision 3000 X Series, User Manual

Search results

Summary of Contents for InfiniiVision 3000 X Series

Reviews:

Related manuals for InfiniiVision 3000 X Series

Brands by name

Popular brands