Keysight Technologies InfiniiVision 3000 X Series User Manual Download Page 328

Page: 328 / 432

328

Keysight InfiniiVision 3000 X-Series Oscilloscopes User's Guide

Reference

Probes and Accessories

For a list of the probes and accessories that are compatible with the 3000 X-Series

oscilloscopes, see the data sheet at:

www.keysight.com/find/3000X-Series

AutoProbe

Interface

Most Keysight single-ended active, differential, and current probes are compatible

with the AutoProbe interface. Active probes that do not have their own external

power supply require substantial power from the AutoProbe interface.

If too much current is drawn from the AutoProbe interface, an error message will

be displayed, indicating that you must momentarily disconnect all probes to reset

the AutoProbe interface, then connect only the supported quantity of active

probes.

Summary of Contents for InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Search results

Summary of Contents for InfiniiVision 3000 X Series

Reviews:

Related manuals for InfiniiVision 3000 X Series

Brands by name

Popular brands

Keysight Technologies InfiniiVision 3000 X Series, User Manual

Search results

Summary of Contents for InfiniiVision 3000 X Series

Reviews:

Related manuals for InfiniiVision 3000 X Series

Brands by name

Popular brands