Keysight Technologies InfiniiVision 3000 X Series User Manual Download Page 220

Page: 220 / 432

220

Keysight InfiniiVision 3000 X-Series Oscilloscopes User's Guide

Measurements

To isolate a pulse for Top measurement

The following figure shows how to use Zoom mode to isolate a pulse for a

Top

measurement.

You may need to change the measurement window setting so that the

measurement is made in the lower, Zoom window. See

"Measurement Window

with Zoom Display"

on page 236.

Base

The Base of a waveform is the mode (most common value) of the lower part of the

waveform, or if the mode is not well defined, the base is the same as Minimum.

The Y cursor shows the value being measured.

Overshoot

Overshoot is distortion that follows a major edge transition expressed as a

percentage of Amplitude. The X cursors show which edge is being measured (edge

closest to the trigger reference point).

Figure 46

Isolating area for Top measurement

Summary of Contents for InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Search results

Summary of Contents for InfiniiVision 3000 X Series

Reviews:

Related manuals for InfiniiVision 3000 X Series

Brands by name

Popular brands

Keysight Technologies InfiniiVision 3000 X Series, User Manual

Search results

Summary of Contents for InfiniiVision 3000 X Series

Reviews:

Related manuals for InfiniiVision 3000 X Series

Brands by name

Popular brands