Keysight Technologies InfiniiVision 3000 X Series User Manual Download Page 35

Page: 35 / 432

Getting Started

Keysight InfiniiVision 3000 X-Series Oscilloscopes User's Guide

Connect probes to all other oscilloscope channels (channel 2 of a 2-channel

oscilloscope, or channels 2, 3, and 4 of a 4-channel oscilloscope).

Repeat the procedure for each channel.

Learn the Front Panel Controls and Connectors

On the front panel,

key

refers to any key (button) you can press.

Softkey

specifically refers to the six keys that are directly below the display. The

legend for these keys is directly above them, on the display. Their functions

change as you navigate through the oscilloscope's menus.

For the following figure, refer to the numbered descriptions in the table that

follows.

Perfectly compensated

Over compensated

Under compensated

Summary of Contents for InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Search results

Summary of Contents for InfiniiVision 3000 X Series

Reviews:

Related manuals for InfiniiVision 3000 X Series

Brands by name

Popular brands

Keysight Technologies InfiniiVision 3000 X Series, User Manual

Search results

Summary of Contents for InfiniiVision 3000 X Series

Reviews:

Related manuals for InfiniiVision 3000 X Series

Brands by name

Popular brands