Keysight Technologies InfiniiVision 3000 X Series User Manual Download Page 110

Page: 110 / 432

110

Keysight InfiniiVision 3000 X-Series Oscilloscopes User's Guide

Digital Channels

Any digital channel with an active signal will be displayed. Any digital channels

without active signals will be turned off.
• To undo the effects of AutoScale, press the

Undo AutoScale

softkey before

pressing any other key.

This is useful if you have unintentionally pressed the

[AutoScale]

key or do not like

the settings AutoScale has selected. This will return the oscilloscope to its

previous settings. See also:

"How AutoScale Works"

on page 33.

To set the instrument to the factory-default configuration, press the

[Default Setup]

key.

Interpreting the digital waveform display

The following figure shows a typical display with digital channels.

Summary of Contents for InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Search results

Summary of Contents for InfiniiVision 3000 X Series

Reviews:

Related manuals for InfiniiVision 3000 X Series

Brands by name

Popular brands

Keysight Technologies InfiniiVision 3000 X Series, User Manual

Search results

Summary of Contents for InfiniiVision 3000 X Series

Reviews:

Related manuals for InfiniiVision 3000 X Series

Brands by name

Popular brands