manualshive.com logo in svg

Keysight Technologies InfiniiVision 3000 X Series, User Manual

The Keysight Technologies InfiniiVision 3000 X Series is a cutting-edge oscilloscope that offers high performance and ease of use. Get the most out of your device by downloading the free user manual from our website. Master your device with detailed instructions and troubleshooting tips at manualshive.com.

Share
Download
background image

292

Keysight InfiniiVision 3000 X-Series Oscilloscopes User's Guide

20

Utility Settings

 

•

LAN

 — When a DSOXLAN LAN/VGA module is installed, you can use the 

LAN 

Settings

 and 

LAN Reset

 softkeys to configure the LAN interface. See 

"Setting 

up the Oscilloscope's LAN Connection"

on page 292.

•

GPIB

 — When a DSOXGPIB GPIB module is installed, you can use the 

Address

 

softkey to configure the GPIB address.

•

There are no configuration settings for the USB interface.

When an I/O interface is installed, remote control over that interface is always 

enabled. Also, the oscilloscope can be controlled via multiple I/O interfaces (for 

example, USB and LAN) at the same time.

See Also

•

Chapter 21

, “Web Interface,” starting on page 311 (when the oscilloscope is 

connected to a LAN).

•

"Remote Programming via the Web Interface"

on page 314

• The oscilloscope's 

Programmer's Guide

.

•

"Remote Programming with Keysight IO Libraries"

on page 316

Setting up the Oscilloscope's LAN Connection

When the DSOXLAN LAN/VGA module is installed, you can place the oscilloscope 

on the network and set up its LAN connection. Once that is done, you can use the 

oscilloscope's web interface or remotely control the oscilloscope via the LAN 

interface.

The oscilloscope supports methods for automated LAN configuration or manual 

LAN configuration (see 

"To establish a LAN connection"

on page 293). It is also 

possible to set up a point-to-point LAN connection between a PC and the 

oscilloscope (see 

"Stand-alone (Point-to-Point) Connection to a PC"

on 

page 294).

Once the oscilloscope is set up on the network, you can use the oscilloscope's 

web page to view or change its network configuration and access additional 

settings (like the network password). See 

Chapter 21

, “Web Interface,” starting on 

page 311.

NOTE

When you connect the oscilloscope to a LAN it is a good practice to limit access to the 

oscilloscope by setting a password. By default, the oscilloscope is not password protected. 

See 

"Setting a Password"

on page 321 to set a password.

Summary of Contents for InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for InfiniiVision 3000 X Series

ABB E-Hub 2.0 Getting Started preview
E-Hub 2.0
Brand: ABB Pages: 18
R-Tech X5 Quick Manual preview
X5
Brand: R-Tech Pages: 3
Raymarine ST7000 Installation Instructions Manual preview
ST7000
Brand: Raymarine Pages: 55
Halyard MIC Series Instructions For Use preview
MIC Series
Brand: Halyard Pages: 4
GAME Underwater Light Show & Fountain Instructions preview
Underwater Light Show & Fountain
Brand: GAME Pages: 2
Labnet D1200 Instruction Manual preview
D1200
Brand: Labnet Pages: 2
Palazzetti P1 Installation Instructions, Use And Maintenance preview
P1
Brand: Palazzetti Pages: 112
Malekko QUAD ENVELOPE Quick Start Manual preview
QUAD ENVELOPE
Brand: Malekko Pages: 2
Major MJ2000 Operator'S Manual preview
MJ2000
Brand: Major Pages: 26
Pace ThermoTweez Handpiece TT-65 Operation & Maintenance Instructions Manual preview
ThermoTweez Handpiece TT-65
Brand: Pace Pages: 14
Dantel 44210 Installation & Operation Manual preview
44210
Brand: Dantel Pages: 22
Eaton Cutler-Hammer ATC-300 Instruction Booklet preview
Cutler-Hammer ATC-300
Brand: Eaton Pages: 32
V-GREAT VG-6777 Installation And Operation Manual preview
VG-6777
Brand: V-GREAT Pages: 4
gartenpirat Spielturm Premium L GP1122 Assembly Instruction Manual preview
Spielturm Premium L GP1122
Brand: gartenpirat Pages: 8
gartenpirat Lisa-Fun GP1604 Assembly Instructions Manual preview
Lisa-Fun GP1604
Brand: gartenpirat Pages: 6
Bayer HealthCare Certegra Operation Manual preview
Certegra
Brand: Bayer HealthCare Pages: 104
Energizer EDC2-1001-RGB-MWT Quick Start Manual preview
EDC2-1001-RGB-MWT
Brand: Energizer Pages: 18
MIETHKE proGAV Instructions For Use Manual preview
proGAV
Brand: MIETHKE Pages: 125

Brands by name

Popular brands

Load more brands