Keysight Technologies InfiniiVision 3000 X Series User Manual Download Page 172

Page: 172 / 432

172

Keysight InfiniiVision 3000 X-Series Oscilloscopes User's Guide

Triggers

USB Trigger

USB trigger will trigger on a Start of Packet (SOP), End of Packet (EOP) signal,

Reset Complete (RC), Enter Suspend (Suspend), or Exit Suspend (Exit Sus) on the

differential USB data lines (D+ and D-). USB Low Speed and Full Speed are

supported by this trigger.

Press

[Default Setup]

Press the

[Label]

key to switch labels on.

Turn on any analog or digital channels that you will be using for the USB

signals.

Figure 32

Using Field Holdoff to Synchronize to Color Field 1 or 3 (Field 1 mode)

End of packet trigger

D-,+

D+,-

Bus Idle

SEO portion of EOP

SOP

Summary of Contents for InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Search results

Summary of Contents for InfiniiVision 3000 X Series

Reviews:

Related manuals for InfiniiVision 3000 X Series

Brands by name

Popular brands

Keysight Technologies InfiniiVision 3000 X Series, User Manual

Search results

Summary of Contents for InfiniiVision 3000 X Series

Reviews:

Related manuals for InfiniiVision 3000 X Series

Brands by name

Popular brands