Huawei ECC800-Pro User Manual Download Page 112

Page: 112 / 368

Power-On Commissioning

Prerequisites

●

The hardware and cable installation check is complete for controller

components according to data center specifications and requirements.

●

The device and ECC800-Pro have been powered on.

●

You have obtained the ECC800-Pro IP address as well as the user name and

password used for WebUI login.

●

A PC with an IP address in the same network segment as the ECC800-Pro IP

address is prepared, and the PC has connected to the WAN1 port on the

ECC800-Pro.

Context

After installing or replacing the device or ECC800-Pro, set monitoring parameters

and add the device.

5.1 Preparations and WebUI Login

Prerequisites

●

Supported operating system: Windows 7 and later versions

●

It is recommended that the screen resolution be 1366 x 768 or higher.

●

Browser: Chrome, Firefox, Internet Explorer 11 or later

Procedure

Step 1 Connect a network cable between the PC network port and the WAN1 port

(protected by a security mechanism) on the ECC800-Pro.

Table 5-1 Default IP addresses for the WAN and LAN ports on the ECC800-Pro

Port

Default IP Address

WAN1

192.168.8.10

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

5 Power-On Commissioning

Issue 02 (2020-09-07)

101

Summary of Contents for ECC800-Pro

















































































































































































































































































































































































Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands

Huawei ECC800-Pro, User Manual

Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands