Huawei ECC800-Pro User Manual Download Page 94

Page: 94 / 368

NO TE

● If the battery string is configured with the neutral wire, measure the currents of the positive

and negative battery string cables. If the battery string is not configured with the neutral

wire, measure the current of either the positive or negative battery string cable. The

following uses the scenario where the battery string is configured with the neutral wire as an

example.

● When an iBOX manages multiple battery strings, first connect the Hall effect sensors on the

positive and negative cables of battery string 1 respectively to the corresponding ports on

the iBOX. Then connect the Hall effect sensors on battery string 2 to the iBOX in the same

way, and so on.

● If the positive or negative battery string cable is too thick to be routed through the Hall

effect sensor, or the measurement range of the Hall effect sensor is not enough, use multiple

Hall effect sensors to monitor the current of one battery string. The iBOX supports the sum

of the monitoring results of multiple Hall effect sensors, which is set through Multi-Hall cur.

setting.

● The value of Multi-Hall cur. setting equals the number of positive or negative Hall effect

sensors in a single battery string and should be greater than or equal to 1.

BCB Port

Figure 3-52 BCB port pins

Table 3-79 BCB_1–BCB_4 port pin definitions

Pin

Defi

nitio

Signal

Description

Status Description

Initial

Status

Descriptio

Monitors

whether the

BCB

connects to

the signal

input port.

● Grounded: BCB

connected.

● Disconnected: BCB

not connected.

Disconnect

The four

BCBs can

separately

manage

tripping of

four

battery

routes.

STA

Monitors

the battery

circuit

breaker

● Grounded: The

battery circuit

breaker is ON.

● Disconnected: The

battery circuit

breaker is OFF.

Disconnect

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

3 Device Description

Issue 02 (2020-09-07)

Summary of Contents for ECC800-Pro

















































































































































































































































































































































































Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands

Huawei ECC800-Pro, User Manual

Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands