Huawei ECC800-Pro User Manual Download Page 350

Page: 350 / 368

Table 8-54 Turning on or off aisle lights

Path

Setting

Monitoring > Aisle > AC

Actuator Group > AC

Actuator n > Running

Parameters

Set Route 1 control mode to Light.
Set Set light mode to Manual.

Monitoring > Aisle > AC

Actuator Group > AC

Actuator n > Controls

Select Remote open scuttle, select ON or OFF as

required, and click Submit.

----End

Example

The following figure shows how to turn on or off the lights controlled by AC

actuator 2.

Figure 8-38 Turning on or off aisle lights

Follow-up Procedure

Set Set light mode to Automatic.

CA UTION

When a smart module actuator is configured, you need to set parameters for the

smart module actuator. The setting process is similar.

8.1.35 How Can I Open Skylights Remotely over the ECC800-

Pro WebUI?

Context

You can open skylights over the ECC800-Pro WebUI in emergencies.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

8 FAQ

Issue 02 (2020-09-07)

339

Summary of Contents for ECC800-Pro

















































































































































































































































































































































































Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands

Huawei ECC800-Pro, User Manual

Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands