Huawei ECC800-Pro User Manual Download Page 299

Page: 299 / 368

2. Add a PD7777 electricity meter.

Table 8-20 Adding a PD7777 electricity meter

Path

Parameter

Setting

Choose

System

Settings >

Device

Management

and click Add

Device.

Device

attribute

Select Electricity Meter from the drop-

down list box.

Device Type

Select CHNT-PD7777-3S3 from the drop-

down list box.

Connect To

Select ECC800 from the drop-down list

box.

Communicati

ons Port

Select COM1 from the drop-down list box.

NOTE

The setting example indicates that the PD7777

electricity meter is connected to the COM1 port

on the ECC800-Pro. If the PD7777 electricity

meter is connected to another port, enter the

number of the connected port.

Device

Address

In this example, Device Address is set to

15. During actual configuration, set the

device address for the PD7777 electricity

meter based on the actual situation.

3. Click Test Connect to check whether the PD7777 electricity meter is properly

connected to the ECC800-Pro.
–

If the PD7777 electricity meter connects to the ECC800-Pro successfully,

click Confirm. The connected devices are displayed in the Number of

connected devices list.

–

If the connection fails, check whether the device is properly connected to

the ECC800-Pro, whether the device and ECC800-Pro are running

properly, and whether the parameter settings are consistent with the

device parameters.

----End

8.1.7.21 How Can I Set and Add a NetCol5000-A011/A025/A035/A042/A050

(Modbus-TCP)?

Prerequisites

One end of the straight-through cable has been connected to the FE_1 port on the

NetCol5000-A011/A025/A035/A042/A050 main control board, and the other end

has been connected to the PoE port on the ETH converter.

Context

The following describes how to set and add a NetCol5000-A042.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

8 FAQ

Issue 02 (2020-09-07)

288

Summary of Contents for ECC800-Pro

















































































































































































































































































































































































Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands

Huawei ECC800-Pro, User Manual

Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands