Huawei ECC800-Pro User Manual Download Page 285

Page: 285 / 368

Path

Parameter

Setting

Connect To

Select ECC800 from the drop-down list

box.

NOTE

If the other end of the straight-through cable is

connected to the COM port on the UIM20A,

select UIM.

Communicati

ons Port

Select COM1 from the drop-down list box.

NOTE

The setting example indicates that the

TP48202B is connected to the COM1 port on

the ECC800-Pro. If the TP48202B is connected

to another port, enter the number of the

connected port.

Device

Address

In this example, Device Address is set to

160. During actual configuration, set the

device address for the DC PDC based on

the actual situation.

3. Click Test Connect to check whether the DC PDC is properly connected to the

ECC800-Pro.
–

If the connection is normal, click Confirm. The connected devices are

displayed in the Number of connected devices list.

–

If the connection is abnormal, check whether the device is properly

connected to the ECC800-Pro, whether the device and the ECC800-Pro are

running properly, and whether the parameter settings are consistent with

the device parameters.

----End

8.1.7.11 How Can I Set and Add a SmartLi (Modbus-TCP)?

Prerequisites

One end of the straight-through cable has been connected to the FE port on the

SmartLi and the other end has been connected to the PoE port on the smart ETH

gateway.

Procedure

Step 1 Set SmartLi monitoring parameters.

1. On the home screen of the SmartLi, tap System Info.
2. Choose System Info > Settings, enter the user name admin and password

000001, and tap

3. Tap Communication to set IP address assign to Automatic(DHCP) on the

displayed communication settings screen and the SmartLi is discovered by

ECC800-Pro automatically and is connected to the ECC800-Pro.

----End

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

8 FAQ

Issue 02 (2020-09-07)

274

Summary of Contents for ECC800-Pro

















































































































































































































































































































































































Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands

Huawei ECC800-Pro, User Manual

Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands