Huawei ECC800-Pro User Manual Download Page 209

Page: 209 / 368

6.6.2 FusionModule800 Linkage Control

Prerequisites

●

You have obtained the IP address of the ECC800-Pro as well as the user name

and password used for WebUI login.

●

A PC with an IP address in the same network segment as that of the ECC800-

Pro is prepared, and the PC has connected to port WAN1 on the ECC800-Pro.

●

Ensure that Enable linkage control function is Yes.

Linkage Grouping

Table 6-38 FusionModule800 linkage grouping

Linkage

Category

Default

Status

Function

Link air

conditioner

fault with

emergency

fan

off

If this linkage status is set to on:
If all smart cooling products fail to communicate, and

the aisle temperature is higher than 27°C, the

emergency fan starts.
If all smart cooling products fail to provide the cooling

function properly, and the aisle temperature is higher

than 27°C, the emergency fan starts.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

6 Feature Description

Issue 02 (2020-09-07)

198

Summary of Contents for ECC800-Pro

















































































































































































































































































































































































Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands

Huawei ECC800-Pro, User Manual

Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands