manualshive.com logo in svg

Huawei ECC800-Pro, User Manual

The Huawei ECC800-Pro offers top-notch performance and advanced features, ensuring seamless communication. Need assistance in setting up or operating this exceptional device? Look no further! Download the user manual for free at manualshive.com and explore its comprehensive instructions and guidelines for a hassle-free experience with your Huawei ECC800-Pro.

Share
Download
background image

Table 8-53 Opening a door remotely

Path

Setting

Monitoring > Aisle >

Access Actuator Group >

Access Actuator n >

Controls

Select Remote door opening and click Submit

 

CA UTION

● Remotely opening the door may open the smart module door, and this may

pose security risks. Exercise caution when performing this operation.

● When a smart module actuator is configured, you need to set parameters for

the smart module actuator. The setting process is similar.

----End

Example

The following figure shows how to remotely open the aisle door controlled by

access actuator 1.

Figure 8-37 Opening a door remotely

8.1.34 How Can I Turn On or Off Aisle Lights in the Smart

Module over the ECC800-Pro WebUI?

Context

●

If O&M personnel forget to turn off lights when exiting the data center, you

can remotely turn off the lights over the ECC800-Pro WebUI.

●

When the local light button is faulty or lights cannot be turned on through a

linkage, you can remotely turn on the lights over the ECC800-Pro WebUI.

Procedure

Step 1 Log in to the ECC800-Pro WebUI as an administrator.

Step 2 Turn on or off aisle lights.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

8 FAQ

Issue 02 (2020-09-07)

Copyright © Huawei Technologies Co., Ltd.

338

Summary of Contents for ECC800-Pro

















































































































































































































































































































































































Reviews:

No comments

Related manuals for ECC800-Pro

Abus FUMO50110 Quick Manual preview
FUMO50110
Brand: Abus Pages: 12
Watts 1717 Installation Instruction preview
1717
Brand: Watts Pages: 2
Hanbay RC Series Manual preview
RC Series
Brand: Hanbay Pages: 18
BabySafe LUCKY Instruction preview
LUCKY
Brand: BabySafe Pages: 24
Caen V793 Technical Information Manual preview
V793
Brand: Caen Pages: 20
Eaton CF2000 Installation And Operation Manual preview
CF2000
Brand: Eaton Pages: 100
Maguire Products GRAVIMETRIC AUGER FEEDER MGF-ST Instruction Manual preview
GRAVIMETRIC AUGER FEEDER MGF-ST
Brand: Maguire Products Pages: 47
Magtrol DSP7000 User Manual preview
DSP7000
Brand: Magtrol Pages: 160
Parker ACR7000 Series Hardware Manual preview
ACR7000 Series
Brand: Parker Pages: 21
Parker AC890PX Series Quick Start Manual preview
AC890PX Series
Brand: Parker Pages: 26
Parallax 700-10016 Manual preview
700-10016
Brand: Parallax Pages: 3
Vageo DT-1 Manual preview
DT-1
Brand: Vageo Pages: 2
YASKAWA FSDrive-MV1000 Series Instructions For Use Manual preview
FSDrive-MV1000 Series
Brand: YASKAWA Pages: 260
YASKAWA iQpump1000 Installation & Start?Up Manual preview
iQpump1000
Brand: YASKAWA Pages: 114
YASKAWA MOTOMAN FS100 Operator'S Manual preview
MOTOMAN FS100
Brand: YASKAWA Pages: 20
YASKAWA yasnac lx3 Maintenance Manual preview
yasnac lx3
Brand: YASKAWA Pages: 152
YASKAWA GPD 506/P5 Technical Manual preview
GPD 506/P5
Brand: YASKAWA Pages: 66
YASKAWA MOTOMAN FS100 Option Addendum preview
MOTOMAN FS100
Brand: YASKAWA Pages: 20

Brands by name

Popular brands

Load more brands