Huawei ECC800-Pro User Manual Download Page 35

Page: 35 / 368

Indicator Color

Name

Status

Description

Yellow

Alarm

indicato

Steady on

The converter generates a

forewarning indicating that

power will be limited due to

ambient overtemperature, or

generates a protection

shutdown alarm due to

ambient overtemperature or

undertemperature.

Power input overvoltage or

undervoltage protection

Reverse DC input connection

Slight current imbalance

Output overvoltage

Hibernation

Off

The converter generates no

protection alarms.

Blinking at

long intervals

The communication between

the converter and the outside is

interrupted (the indicator blinks

at 0.5 Hz, on for 1s and then

off for 1s).

Red

Fault

indicato

Steady on

The converter locks out due to

output overvoltage.

The converter delivers no

output due to internal faults.

Off

The converter is working

properly.

3.2 Southbound Device Introduction

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

3 Device Description

Issue 02 (2020-09-07)

Summary of Contents for ECC800-Pro

















































































































































































































































































































































































Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands

Huawei ECC800-Pro, User Manual

Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands