manualshive.com logo in svg

Huawei ECC800-Pro, User Manual

The Huawei ECC800-Pro offers top-notch performance and advanced features, ensuring seamless communication. Need assistance in setting up or operating this exceptional device? Look no further! Download the user manual for free at manualshive.com and explore its comprehensive instructions and guidelines for a hassle-free experience with your Huawei ECC800-Pro.

Share
Download
background image

1. On the Linkage Group tab page, click the Link smoke alarm with skylight

open entry.

2. On the Linkage Logic List tab page, click Add.
3. Set parameters for the Link smoke alarm with skylight open.

Figure 6-61 Link smoke alarm with skylight open logic

4. Click Submit.

Step 11 Ensure that Link smoke alarm with skylight open on the Linkage Group tab

page is on.

NO TE

Click Link smoke alarm with skylight open on the Linkage Group tab page. If it is in on state,

the corresponding logic configurations on the Linkage Logic List tab page are available. If it is

in off state, the corresponding logic configurations on the Linkage Logic List tab page are

unavailable.

Step 12 Check the Link smoke alarm with skylight open linkage function.

Table 6-37 Function check

Check Method

Expected Result

When the skylight in the aisle is

closed, press the skylight button to

open the skylight.

● Smoke DI alarm is displayed on

the active alarm page of the app or

WebUI.

● The skylight is opened.

Simulate a smoky environment under

the smoke sensor or the multi-func

sensor.

 

----End

Follow-up Procedure

After Link smoke alarm with skylight open linkage is triggered and the alarm is

cleared, perform the following operations:

●

Press the reset button on the smoke sensor to clear the alarm.

●

Close the skylight manually.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

6 Feature Description

Issue 02 (2020-09-07)

Copyright © Huawei Technologies Co., Ltd.

197

Summary of Contents for ECC800-Pro

















































































































































































































































































































































































Reviews:

No comments

Related manuals for ECC800-Pro

IBM 3708 End-User Reference preview
3708
Brand: IBM Pages: 144
Daikin Madoka User Manual preview
Madoka
Brand: Daikin Pages: 2
Daikin BRC7E530W8 Operation Manual preview
BRC7E530W8
Brand: Daikin Pages: 12
Daikin BRC1H81K Installation And Operation Manual preview
BRC1H81K
Brand: Daikin Pages: 12
Daikin BRC1H71W Operation Manual preview
BRC1H71W
Brand: Daikin Pages: 46
Daikin BRC1D71 Operation Manual preview
BRC1D71
Brand: Daikin Pages: 21
Daikin BRC1D517 Operation Manual preview
BRC1D517
Brand: Daikin Pages: 20
Danfoss VLT AutomationDrive FC 302 Installation Manual preview
VLT AutomationDrive FC 302
Brand: Danfoss Pages: 128
Danfoss VLT DriveMotor FCP 106 Installation Instructions preview
VLT DriveMotor FCP 106
Brand: Danfoss Pages: 4
OES ISC-9000 Operational Instructions preview
ISC-9000
Brand: OES Pages: 3
Samwontech TEMP2000 Series Installation Manual preview
TEMP2000 Series
Brand: Samwontech Pages: 91
Warren rupp HDF3-A Original Instructions Manual preview
HDF3-A
Brand: Warren rupp Pages: 18
Yamaha QL5 Manual preview
QL5
Brand: Yamaha Pages: 100
ZKTeco MA500 Installation Manual & User Manual preview
MA500
Brand: ZKTeco Pages: 20
ZKTeco ProFace X Installation Manual preview
ProFace X
Brand: ZKTeco Pages: 8
ZKTeco TF1600 ZKTeco Quick Start Manual preview
TF1600 ZKTeco
Brand: ZKTeco Pages: 10
ZKTeco SpeedFace-V3L User Manual preview
SpeedFace-V3L
Brand: ZKTeco Pages: 121
ZKTeco FaceDepot-7BL Quick Start Manual preview
FaceDepot-7BL
Brand: ZKTeco Pages: 12

Brands by name

Popular brands

Load more brands