Huawei ECC800-Pro User Manual Download Page 320

Page: 320 / 368

----End

8.1.7.38 How Can I Commission a Temperature Sensor (Connected to the

NTC Port on the T/H Sensor)?

If a temperature sensor is installed, perform the following steps to configure it.

Prerequisites

Cables have been connected to the NTC, T/H sensor, and UIM20A expansion

module.

Figure 8-21 Wiring diagram

(1) UIM20A expansion module

(2) T/H sensor

(3) NTC sensor

Procedure

Step 1 The NTC port on the T/H sensor connected to the temperature sensor supports

automatic identification. Therefore, you do not need to set parameters.

Step 2 Add the T/H sensor.

1. Log in to the ECC800-Pro WebUI as an administrator.
2. Add the T/H sensor.

Choose System Settings > Device Management and click Auto Discover

Device to add the T/H sensor. The device connection information is displayed.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

8 FAQ

Issue 02 (2020-09-07)

309

Summary of Contents for ECC800-Pro

















































































































































































































































































































































































Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands

Huawei ECC800-Pro, User Manual

Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands