Huawei ECC800-Pro User Manual Download Page 131

Page: 131 / 368

Item

Alarm Severity

Selection

Description

Critical, Major,

Minor, Warning

NOTE

– Critical: red light
– Major: orange light
– Minor: yellow light
– Warning: white light

None

The eLight strip light is steady

blue (atmosphere light).

NOTE

After you set the alarm severity, the eLight indicator is off if no alarm is generated.

Step 4 If there are multiple eLights, repeat

Step 1

–

Step 3

----End

5.8 Commissioning the PDU2000 (for

FusionModule800)

When the system type is FusionModule800 and a PDU2000 is installed, perform

the following steps to configure it.

Prerequisites

One end of the straight-through cable has been connected to the COM port on

the PDU2000 and the other end has been connected to the COM port on the ETH

converter.

Context

Table 5-12 PDU2000 basic Information

Vendor

Name

Displayed on

the WebUI

Eleventh and Twelfth

Characters in Device

Barcode

Clever

PDU2000-M(C)

Haipengxin

PDU2000-M(H)

a: The barcode starts with 21 and is attached to the device.

Procedure

Step 1 Set the PDU2000 monitoring parameters.

●

Set the PDU2000-M (C) monitoring parameters.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

5 Power-On Commissioning

Issue 02 (2020-09-07)

120

Summary of Contents for ECC800-Pro

















































































































































































































































































































































































Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands

Huawei ECC800-Pro, User Manual

Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands