Huawei ECC800-Pro User Manual Download Page 58

Page: 58 / 368

Indicator Color

Name

Status

Description

RF_Z

Green Communicati

on status

indicator

Steady on

No network parameters

exist, or a network is to be

created.

Blinking at

long

intervals

A network is set up, and no

node access is allowed (the

indicator blinks at 0.5 Hz, on

for 1s and then off for 1s).

Blinking at

super short

intervals

A network is being set up,

and node access is allowed

(the indicator blinks at 10

Hz, on for 0.05s and then off

for 0.05s).

Blinking

intermittent

ly at super

short

intervals

The smart module actuator

is searching for a network

(the indicator blinks at super

short intervals for 0.5s and

then turns off for 0.5s).

3.2.6 AC Actuator

The AC actuator is used in a smart module to control the lighting inside the smart

module by receiving commands from the access control system or host, infrared

linkage information (disabled by default), or signals from the light button. It also

provides a charging port for the PAD (AC OUT2).

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

3 Device Description

Issue 02 (2020-09-07)

Summary of Contents for ECC800-Pro

















































































































































































































































































































































































Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands

Huawei ECC800-Pro, User Manual

Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands