Huawei ECC800-Pro User Manual Download Page 341

Page: 341 / 368

8.1.28 How Can I Add Devices Accessed Through the ETH

Converter to the ECC800-Pro WebUI?

Context

Figure 8-33 Network diagram

Procedure

Step 1 Set communications parameters on the device.

Table 8-46 Description of communications parameters to be set on a device

Parameter

Recommended Value

Baud rate

This section uses 9600 as an example. Set this

parameter based on site requirements.

NOTE

For certain devices, this parameter does not need to be set.

Communications

address

This section uses 1 as an example. Set this parameter

based on site requirements.

Step 2 Add the device to the ECC800-Pro WebUI.

1. Log in to the ECC800-Pro WebUI as an administrator.
2. Add the device.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

8 FAQ

Issue 02 (2020-09-07)

330

Summary of Contents for ECC800-Pro

















































































































































































































































































































































































Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands

Huawei ECC800-Pro, User Manual

Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands