Huawei ECC800-Pro User Manual Download Page 78

Page: 78 / 368

Figure 3-34 ETH converter

(1) Status indicator

(2) BLINK button

(3) COM1 communications port

(4) COM2 communications port

(5) 48 V power port

(6) PoE port

Specifications

Table 3-60 ETH converter technical specifications

Item

Specifications

Power

input

● DC input: terminal, with an input voltage of 36 V DC–60 V DC
● PoE power supply: one PoE port, 10/100M communication rate,

complying with IEEE802.3at

RS485/CA

Provides two RS485/CAN ports. The default communications rate

for the RS485 port is 9600 bit/s, and that for the CAN port is 125

kbit/s. Both ports match the RJ45 terminal shared by RS485 and

CAN.

BLINK

button

If you press the BLINK button, the RUN indicator blinks

intermittently at super short intervals (blinking at super short

intervals for 0.5s and then off for 0.5s) for 10 seconds.

E-label

Supported

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

3 Device Description

Issue 02 (2020-09-07)

Summary of Contents for ECC800-Pro

















































































































































































































































































































































































Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands

Huawei ECC800-Pro, User Manual

Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands