Huawei ECC800-Pro User Manual Download Page 62

Page: 62 / 368

Specifications

Table 3-43 Skylight actuator technical specifications

Item

Specifications

Power input

● DC input: terminal, with an input voltage of 36 V DC–60 V

● PoE power supply: one PoE port that complies with

IEEE802.3at

PoE port

FE communication with the rate of 10/100 Mbit/s

Wireless

communicatio

One wireless port that complies with IEEE 802.15.4, mutual

backup with FE communication

AI/DI port

Two AI/DI ports for detecting fire extinguishing linkage signals;

smoke detection signals also supported

DO output

One 12 V DC power output for controlling the skylight

magnetic lock; driving nine skylight magnetic locks

simultaneously

DI input

One DI input port for connecting to the window open button

BLINK button

● Press the button for less than 1 second to start blinking.
● Hold down the button for 1–5 seconds to search for a

network and start networking.

● Hold down the button for more than 10 seconds to clear

network parameters.

Address DIP

switch

4-pin address DIP switch

E-label

Supported

Indicators

Table 3-44 Skylight actuator indicators

Indicator Color

Name

Status

Description

Power

Green Power input

status

indicator

Steady on

The power input is normal.

Off

There is no power input.

RUN

Green Running

status

indicator

Off

The power is abnormal or

the board program is

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

3 Device Description

Issue 02 (2020-09-07)

Summary of Contents for ECC800-Pro

















































































































































































































































































































































































Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands

Huawei ECC800-Pro, User Manual

Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands