Huawei ECC800-Pro User Manual Download Page 284

Page: 284 / 368

Path

Parameter

Setting

Communicati

ons Port

Select COM2 from the drop-down list box.

NOTE

The setting example indicates that the Envicool

IFX Terminal is connected to the COM2 port on

the ECC800-Pro. If the Envicool IFX Terminal is

connected to another port, enter the number of

the connected port.

Device

Address

In this example, Device Address is set to 1.

During actual configuration, set the device

address for the air conditioner based on

the actual situation.

3. Click Test Connect to check whether the Envicool air conditioner is properly

connected to the ECC800-Pro.
–

If the connection is normal, click Confirm. The connected devices are

displayed in the Number of connected devices list.

–

If the connection is abnormal, check whether the device is properly

connected to the ECC800-Pro, whether the device and the ECC800-Pro are

running properly, and whether the parameter settings are consistent with

the device parameters.

----End

8.1.7.10 How Can I Set and Add a TP48202B (Modbus-RTU)?

Prerequisites

One end of the straight-through cable has been connected to the RS485/RS232

port on the power distribution monitoring unit in the DC PDC, and the other end

has been connected to the COM port on the ECC800-Pro collector or UIM20A.

Procedure

Step 1 Add a TP48202B (Modbus-RTU).

1. Log in to the ECC800-Pro WebUI as an administrator.
2. Add a TP48202B.

Table 8-10 Adding a TP48202B

Path

Parameter

Setting

Choose

System

Settings >

Device

Management

and click Add

Device.

Device

Attribute

Select PDU from the drop-down list box.

Device Type

Select TP48202BDCEndCabinet from the

drop-down list box.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

8 FAQ

Issue 02 (2020-09-07)

273

Summary of Contents for ECC800-Pro

















































































































































































































































































































































































Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands

Huawei ECC800-Pro, User Manual

Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands