Huawei ECC800-Pro User Manual Download Page 281

Page: 281 / 368

8.1.7.8 How Can I Set and Add an SVG-In-Power (Modbus-RTU)?

Prerequisites

One end of the straight-through cable has been connected to pins 4 and 9 of the

COM port on the SVG display, and the other end has been connected to the COM

port on the ECC800-Pro.

NO TE

Pin 4 defines 485+, and pin 9 defines 485–.

Procedure

Step 1 Set SVG display parameters.

1. Tap Expert Setting. On the displayed SVG communication settings screen, set

ID to 1 and Baud to 9600.

NO TE

ID is the communication address, ranging from 1 to 255. This operation uses 1 as an

example.

Figure 8-10 Setting SVG parameters

Step 2 Add an SVG.

1. Log in to the ECC800-Pro WebUI as an administrator.
2. Add an SVG.

Table 8-7 Adding an SVG

Path

Parameter

Setting

Choose

System

Settings >

Device

Management

Device

attribute

Select PDU from the drop-down list box.

Device Type

Select SVG-In-Power from the drop-down

list box.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

8 FAQ

Issue 02 (2020-09-07)

270

Summary of Contents for ECC800-Pro

















































































































































































































































































































































































Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands

Huawei ECC800-Pro, User Manual

Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands