Huawei ECC800-Pro User Manual Download Page 22

Page: 22 / 368

Overview

2.1 Positioning

The ECC800-Pro is the core component for the smart module local management.

It is intelligent, flexible in connection, easy to maintain, and reliable. It adopts the

POE bus for expansion, and allows all intelligent monitoring devices to be flexibly

laid out so that it can manage the devices in the smart module.

2.2 Features

●

Efficient
–

Supports access of wireless devices and provides backup routes, reducing

cable layout workload and enhancing reliability.

–

Supports unlocking through the access card, password, fingerprint and

facial recognition.

–

Supports remote alarm notifications by SMS and email.

–

Supports power supply and communication over the power over Ethernet

(POE) bus, providing rich bandwidth resources and high communication

efficiency.

–

Supports remote upgrade, fault data export, and configuration parameter

synchronization.

–

Eight access control devices and four cameras can be connected to a

single smart module.

–

Cascades a maximum of three ECC800-Pros. The active alarms and power

usage effectiveness (PUE) data of cascaded ECC800-Pros can be displayed

on the WebUI of one ECC800-Pro.

–

Collects statistics on the instantaneous PUE and average PUE of the

smart module and displays the statistics on a dashboard and in curves, so

that you can query the power consumption of the smart module in real

time.

–

Supports the function of transparent transmission over the RS485 port, so

that southbound components can communicate with the NetEco after

accessing the ECC800-Pro.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

2 Overview

Issue 02 (2020-09-07)

Summary of Contents for ECC800-Pro

















































































































































































































































































































































































Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands

Huawei ECC800-Pro, User Manual

Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands