manualshive.com logo in svg

Hitachi SH7750 series, Hardware Manual

The Hitachi SH7750 series embodies cutting-edge technology and unparalleled performance. Our comprehensive "Hardware Manual" provides in-depth details and step-by-step instructions to ensure optimal utilization of this exceptional product. Download it for "free" at manualshive.com and unlock the full potential of your Hitachi SH7750 series device.

Share
Download
background image

Rev. 6.0, 07/02, page 168 of 986

When an FPU operation instruction is executed, the FPU exception cause field is cleared to
zero first. When the next FPU exception is occured, the corresponding bits in the FPU
exception cause field and FPU exception flag field are set to 1. The FPU exception flag field
holds the status of the exception generated after the field was last cleared.

•

 

RM: Rounding mode

RM = 00: Round to Nearest

RM = 01: Round to Zero

RM = 10: Reserved

RM = 11: Reserved

•

 

Bits 22 to 31: Reserved

These bits are always read as 0, and should only be written with 0.

6.3.3

Floating-Point Communication Register (FPUL)

Information is transferred between the FPU and CPU via the FPUL register. The 32-bit FPUL
register is a system register, and is accessed from the CPU side by means of LDS and STS
instructions. For example, to convert the integer stored in general register R1 to a single-precision
floating-point number, the processing flow is as follows:

R1 

→

 (LDS instruction) 

→

 FPUL 

→

 (single-precision FLOAT instruction) 

→

 FR1

6.4

Rounding

In a floating-point instruction, rounding is performed when generating the final operation result
from the intermediate result. Therefore, the result of combination instructions such as FMAC,
FTRV, and FIPR will differ from the result when using a basic instruction such as FADD, FSUB,
or FMUL. Rounding is performed once in FMAC, but twice in FADD, FSUB, and FMUL.

There are two rounding methods, the method to be used being determined by the RM field in
FPSCR.

•

 

RM = 00: Round to Nearest

•

 

RM = 01: Round to Zero

Round to Nearest: The value is rounded to the nearest expressible value. If there are two nearest
expressible values, the one with an LSB of 0 is selected.

If the unrounded value is 2

Emax

 (2 – 2

–P

) or more, the result will be infinity with the same sign as the

unrounded value. The values of Emax and P, respectively, are 127 and 24 for single-precision, and
1023 and 53 for double-precision.

Summary of Contents for SH7750 series














































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7750 series

Danfoss VLT OneGearDrive Operating Manual preview
VLT OneGearDrive
Brand: Danfoss Pages: 44
Danfoss VLT OneGearDrive Installation Instructions Manual preview
VLT OneGearDrive
Brand: Danfoss Pages: 21
Danfoss OMS Instruction preview
OMS
Brand: Danfoss Pages: 20
V2 LEX-RM Manual preview
LEX-RM
Brand: V2 Pages: 20
Westerbeke 108B SIX Operators Manual And Installation Manual preview
108B SIX
Brand: Westerbeke Pages: 112
Eaton Char-Lynn H Series Manual preview
Char-Lynn H Series
Brand: Eaton Pages: 13
Vanguard 61G200 Operator'S Manual preview
61G200
Brand: Vanguard Pages: 120
RADEMACHER RolloTube S Safety Instruction preview
RolloTube S
Brand: RADEMACHER Pages: 60
Navistar MaxxForce 15 Service Manual preview
MaxxForce 15
Brand: Navistar Pages: 24
E-MAG 200-6XC Series Installation And Operating Manual preview
200-6XC Series
Brand: E-MAG Pages: 30
Hatz 2G40 Operator'S Manual preview
2G40
Brand: Hatz Pages: 94
Eastwood 13542 Instructions Manual preview
13542
Brand: Eastwood Pages: 20
MerCruiser Sterndrive TDI 3.0L User Manual preview
Sterndrive TDI 3.0L
Brand: MerCruiser Pages: 119
Lycoming TEO-540 Series User'S Manual And Troubleshooting Manual preview
TEO-540 Series
Brand: Lycoming Pages: 38
YS DZ170 Operator'S Manual preview
DZ170
Brand: YS Pages: 2
Yanmar 2GM20 Operation Manual preview
2GM20
Brand: Yanmar Pages: 63
GEIGER SOLIDline GU45 Series Original Assembly And Operating Instructions preview
SOLIDline GU45 Series
Brand: GEIGER Pages: 12
Honda GX35T Manual preview
GX35T
Brand: Honda Pages: 46

Brands by name

Popular brands

Load more brands