Grandstream Networks UCM6510 User Manual Download Page 40

Page: 40 / 483

P a g e

UCM6510 IP PBX User Manual

Version 1.0.20.31



Added support for wakeup service module in Custom privilege. [Custom Privilege]



Added IPv6 support for T.38.



Added DAHDI settings. [DAHDI Settings]



Added ability to pass through SIP Call-Info header to support GXP phone JPEG_Over_HTTP with

encryption and authentication to open door for GDS3710. [Transparent Call-Info header]

Firmware Version 1.0.13.14



Added extension whitelist/blacklist for IVR dialing. [IVR]



Added ability to include DOD in PPI Header for SIP trunk. [PPI Mode]



Added ability to customize PAI Header. [PAI Header]



Added blacklist for outbound calls. [Outbound Blacklist]



Added support to upload/download MOH package from Web GUI. [MUSIC ON HOLD]



Added support to download custom prompts from Web GUI. [Download All Custom Prompt]



Added option to configure prompt timeout in Dial By Name. [DIAL BY NAME]



Added description field in ZeroConfig settings to configure Softkey/Line/MPK for GXP series phones.

[PROVISIONING]



Improved seamless transfer privilege control. [Seamless transfer privilege control]



Added RTP Keep-alive support. [RTP Keep-alive]



Added Email Send Log. [Email Send Log]



Added support for Mitel simulation/protocol interfaces for PMS module. [PMS INTEGRATION]



Added support for up to 10 failover trunks. [Use Failover Trunk]

Firmware Version 1.0.12.19



Added support for binding a mobile phone number to extension. [Mobile Phone Number]



Added support OPUS codec.



Added support call-barging privilege settings based on extensions. [Monitor privilege control]



Added support for Seamless Transfer. [Enable Seamless Transfer]



Added support for Custom Call-Info for Auto Answer. [Custom Call-info for Auto Answer]



Added support for DND Whitelist. [Do Not Disturb]



Added Field Description on Softkey, Line keys and MPK from Zero Config.



Added support to select interval for numbers on Batch add extension. [Extension Incrementation]



Added support for Batch Add CallerID Number. [CallerID Number]



Added support for Search Extensions Using CallerID Name.



Added support to Enable/Disable Inbound and Outbound Route [Disable This Route / Disable This

Route]



Added support for Outbound Route Time Condition. [Time Condition]



Added support for IPv6. [IPv6 Address]



Added support for MTU configurable. [MTU]



Added support of CRM. [CRM]

Summary of Contents for UCM6510




































































































































































































































































































































































































































































































Search results

Summary of Contents for UCM6510

Reviews:

Related manuals for UCM6510

Brands by name

Popular brands

Grandstream Networks UCM6510, User Manual

Search results

Summary of Contents for UCM6510

Reviews:

Related manuals for UCM6510

Brands by name

Popular brands