Grandstream Networks UCM6510 User Manual Download Page 381

Page: 381 / 483

P a g e

380

UCM6510 IP PBX User Manual

Version 1.0.20.31

SIP Settings/Misc

Table 118: SIP Settings/Misc

Outbound SIP Registrations

Register Timeout

Configure the register retry timeout (in seconds). The default setting is 20.

Register Attempts

Configure the number of registration attempts before the UCM6510 gives

up. The default setting is 0, which means the UCM6510 will keep trying until

the server side accepts the registration request.

Video

Max Bit Rate (kb/s)

Configure the maximum bit rate (in kb/s) for video calls.

The default setting is 384.

Support SIP Video

Select to enable video support in SIP calls.

The default setting is "Yes".

Reject Non-Matching INVITE

If enabled, when rejecting an incoming INVITE or REGISTER request, the

UCM6510 will always reject with "401 Unauthorized" instead of notifying the

requester whether there is a matching user or peer for the request. This

reduces the ability of an attacker to scan for valid SIP usernames.

The default setting is "No".

SDP Attribute Passthrough

Enable Attribute

Passthrough

If enabled, and UCM receives a call that contains unknown

FEC/FECC/FBCP attributes, they will be passed through the UCM

unmodified.

Early Media

Enable Use Final SDP

If enabled, call negotiation will use final response SDP.

Blind Transfer

Allow callback when blind

transfer fails

If enabled, the UCM will call back to the transferrer when blind transfer fails

(due to the destination being busy or not answering. Note: This feature

applies only to internal calls.).

Note:

This feature takes effect only on internal calls.

Blind transfer timeout

Configure the amount of time in seconds that the transferred party will wait

for the destination to answer before being redirected back to the transferrer.

Default is 60 seconds.

DNS

DNS mode

This option affects the DNS query only during Calls. When you choose

A&AAAA, UCM will do both A and AAAA type DNS query; when you chose

A, UCM will only do A type DNS query; and when you chose AAAA, UCM

will only do AAAA type DNS query.

Hold

Summary of Contents for UCM6510




































































































































































































































































































































































































































































































Search results

Summary of Contents for UCM6510

Reviews:

Related manuals for UCM6510

Brands by name

Popular brands

Grandstream Networks UCM6510, User Manual

Search results

Summary of Contents for UCM6510

Reviews:

Related manuals for UCM6510

Brands by name

Popular brands