Grandstream Networks UCM6510 User Manual Download Page 213

Page: 213 / 483

P a g e

212

UCM6510 IP PBX User Manual

Version 1.0.20.31

IPVT Mode

If enabled, it will allow SDP passthrough to Grandstream IPVideoTalk

therefore it will allow calls between the UCM and IPVideoTalk. The default

setting is disabled.

Sync LDAP Enable

If enabled, the local UCM6510 will automatically provide and update the

local LDAP contacts to the remote UCM6510 SIP peer trunk.

In order to ensure successful synchronization, the remote UCM6510 peer

also needs to enable this option on the SIP peer trunk. The default setting

is "No".

Sync LDAP Password

This is the password used for LDAP contact file encryption and decryption

during the LDAP sync process. The password must be the same on both

UCM6510 peers to ensure successful synchronization.

Sync LDAP Port

Configure TCP port used LDAP sync feature between two peer UCM6510.

LDAP Outbound Rule

Specify an outbound rule for LDAP sync feature. UCM6510 will

automatically modify the remote contacts by adding prefix parsed from this

rule.

LDAP Dialed Prefix

Specify the prefix for LDAP sync feature. The UCM6510 will automatically

modify the remote contacts by adding this prefix.

CC Settings

Enable CC

If enabled, the system will automatically alert the user when a called party

is available, given that a previous call to that party failed for some reason.

CC Max Agents

Configure the maximum number of CCSS agents which may be allocated

for this channel. In other words, this number serves as the maximum

number of CC requests this channel is allowed to make. The minimum

value is 1.

CC Max Monitors

Configure the maximum number of monitor structures which may be

created for this device. In other words, this number tells how many callers

may request CC services for a specific device at one time. Min. value is 1.

Table 62: Create New IAX Trunk

Type

Select the VoIP trunk type.



Peer IAX Trunk



Provider Name

Configure a unique label to identify this trunk when listed in outbound rules,

inbound rules and etc.

Host Name

Configure the IP address or URL for the VoIP provider’s server of the trunk.

Keep Trunk CID

If enabled, the trunk CID will not be overridden by extension's CID when

the extension has CID configured. The default setting is "No".

Username

Enter the username to register to the trunk from the provider when

Summary of Contents for UCM6510




































































































































































































































































































































































































































































































Search results

Summary of Contents for UCM6510

Reviews:

Related manuals for UCM6510

Brands by name

Popular brands

Grandstream Networks UCM6510, User Manual

Search results

Summary of Contents for UCM6510

Reviews:

Related manuals for UCM6510

Brands by name

Popular brands