Grandstream Networks UCM6510 User Manual Download Page 448 | Manualshive

Page: 448 / 483

background image

P a g e

|

447

UCM6510 IP PBX User Manual

Version 1.0.20.31

HA100 Configuration

The High Availability settings are available under the Web UI



System Settings



HA

. The following table

describes the HA options:

Table 151: System Settings



HA



HA Settings

High Available Enable

Enables/disables the HA functionality. By default, is Disabled.

Hardware Scan

Select the hardware interface to be scanned, and the system will determine

whether the interface is faulty.

Fault Switch

When the selected hardware interfaces have fault, the backup UCM6510

take over services after master/slave handover. If not checked, UCM only

report fault alarm.

Heartbeat Port

Specifies the heartbeat port. Default setting is: 9527 and valid range is from

0 to 65535.

Heartbeat Timeout Period (s)

Specifies the heartbeat timeout period. If timeout occurs, slave UCM will
take over master’s service. Default setting is: 7(s) and valid range is from

0 to 9.

File Backup Interval(min)

Specifies the file backup interval period which synchronize the relevant files

to standby UCM at any given time (including records, voice mail, voice files,

etc.). Default setting is 30(min) and valid range is from 30 to 720.

Note

: Users can verify the HA status under the

Web GUI



System Settings



HA



HA Status

and

HA

Log

pages which display the relevant information about the HA connection between the UCM6510 and the

HA100, such HA Status, role of the current UCM, HA backup Status, HA backup log, HA switch log and etc.

Upgrading HA100

As we advise to always keep maintaining and upgrading the firmware on all your Grandstream devices,

users could download the latest firmware version for the HA100 from the following link:

http://www.grandstream.com/support/firmware/

After this, please follow below steps in order to upgrade the unit:

1. From the web GUI, navigate under the menu

System

Settings



HA



HA Deconcentrator

Firmware Upgrade.

2.

Ensure that the active UCM’s RS485 cable is connected to the HA device.

3. Press the

Reset

button on the HA100 unit.

4. Upload the downloaded firmware file.

«
...
446
447
448
449
450
...
»

Summary of Contents for UCM6510




































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for UCM6510

Brand: i-MO Pages: 58

eXtremeRAID 1100

Brand: Mylex Pages: 74

Brand: IDT Pages: 93

RabbitCore RCM4400W

Brand: Rabbit Pages: 126

ControlPoint 2000

Brand: 4Home Pages: 20

TE100-S16 - 10/100Mbps Ethernet Switch

Brand: TRENDnet Pages: 15

Brand: Kontron Pages: 42

Brand: TP-Link Pages: 7

Brand: Moxa Technologies Pages: 36

Brand: Sony Ericsson Pages: 93

Brand: Digisol Pages: 73

Brand: Dinstar Pages: 103

Brand: Telit Wireless Solutions Pages: 37

ClareVision CV-M161620-04

Brand: Clare Controls Pages: 32

Brand: IEI Technology Pages: 106

Brand: Xtatix Pages: 12

Brand: netsys Pages: 243

Brand: ICP DAS USA Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands