Grandstream Networks UCM6510 User Manual Download Page 308

Page: 308 / 483

P a g e

307

UCM6510 IP PBX User Manual

Version 1.0.20.31

Table 93: Call Center Parameters

Enable Virtual Queue

Enable virtual queue to activate call center features.

Virtual Queue Period

Configure the amount of seconds a caller must wait before the virtual queue

prompts is played to them. Default is 20 sec.

Virtual Queue Mode

Timeout Mode:

After the virtual queue period passes, the caller will enter the

virtual call queue and be presented with a menu to choose an option, the choices

can be customized from Global Queue Settings page.

DTMF Mode:

on this mode, the callers can activate the virtual queue by pressing

2, then they will be presented with the menu to choose an option as bellow:



Press * to set current number as callback number.



Press 0 to set a callback number different than current caller number.



Press # to keep waiting on the call queue.

Virtual Queue

Outbound Prefix

System will add this prefix to dialed numbers when calling back users.

Enable Virtual Queue

Timeout

If enabled agents will have a set amount of time to answer a virtual queue

callback.

Write Timeout

Configure the virtual queue callback timeout period in seconds.

Enable Position

Announcement

If enabled, callers’ position in queue will be announced based on the frequency

set in

Position Announcement Interval

Note

: Queue position will be announced to the caller upon entering the queue.

Position

Announcement

Interval

Configure the frequency of the caller position announcement.

Enable Hold time

Announcement

Enable the announcement of the estimated hold time to the caller periodically.

Note

: Hold time will not be announced if less than one minute.

Queue Chairman

Select the extension to act as chairman of the queue (monitoring).

Note

: One queue can have up to 3 chairmen.

Enable Agent Login

Enables quick static agent login/logout via GXP21xx softkeys. Supports

GXP21XX endpoint on firmware 1.0.9.18 and higher.

Notes



After enabling the feature, users need to set the option on GXP21XX phone

under “

Account



SIP Settings



Advanced Features



Special Feature

”

to “UCM Call Center” to display a softkey on the phone to login/logout.



When this option is enabled, dynamic agent login will be no longer

supported.



In case of concurrent registrations, changing agent status on one phone

(login/logout) will be reflected on all phones.

Summary of Contents for UCM6510




































































































































































































































































































































































































































































































Search results

Summary of Contents for UCM6510

Reviews:

Related manuals for UCM6510

Brands by name

Popular brands

Grandstream Networks UCM6510, User Manual

Search results

Summary of Contents for UCM6510

Reviews:

Related manuals for UCM6510

Brands by name

Popular brands