Grandstream Networks UCM6510 User Manual Download Page 160

Page: 160 / 483

P a g e

159

UCM6510 IP PBX User Manual

Version 1.0.20.31



Enable Remote Voicemail

: Forward the notify message from

remote voicemail system for the user, and the local voicemail will

be disabled.

Note:

Remote voicemail feature is used only for

Infomatec (Brazil).

SIP/IAX Password

Configure the SIP/IAX password for the users. Two options are available to

create password for the batch of extensions.



Random Password (enter letter

‘r’

) = A random secure password will

be automatically generated. It is recommended to use this password for

security purpose.



Enter a password to be used on all the extensions in the batch.

Voicemail Password

Configure the password to access the extension's voicemail. A randomly

generated password is used by default and is highly recommended for

security. Only digits are supported.

CallerID Number

Configure CallerID Number when adding Batch Extensions.



Use Extension as Number (enter letter

‘e’

)

Users can choose to use the extension number as CallerID.



Use as Number

Users can choose to set a specific number instead of using the

extension number as CallerID.

Ring Timeout

Configure the number of seconds to ring the user before the call is

forwarded to voicemail (voicemail is enabled) or hang up (voicemail is

disabled). If not specified, the default ring timeout is 60 seconds on the

UCM6510, which can be configured in the global ring timeout setting under

Web GUI



Internal Options

: General Preference. The valid range is

between 5 seconds and 600 seconds.

Note:

If the end point also has a ring timeout configured, the actual ring

timeout used is the shortest time set by either device.

Auto Record

Enable automatic recording for the calls using this extension. The default

setting is disabled. The recording files will be saved in external storage if

plugged in and can be accessed under Web GUI



CDR



Recording Files

Skip Voicemail Password

Verification

If enabled, users can skip password verification when dialing in via the My

Voicemail feature code. This option is disabled by default.

Music On Hold

Select which Music On Hold playlist to suggest to extensions when putting

them on hold.

Enable LDAP

If enabled, the batch added extensions will be added to LDAP Phonebook

PBX list; if disabled, the batch added extensions will be skipped when

creating LDAP Phonebook.

Enable WebRTC Support

If enabled, extensions will be able to login to user portal and use Web RTC

Summary of Contents for UCM6510




































































































































































































































































































































































































































































































Search results

Summary of Contents for UCM6510

Reviews:

Related manuals for UCM6510

Brands by name

Popular brands

Grandstream Networks UCM6510, User Manual

Search results

Summary of Contents for UCM6510

Reviews:

Related manuals for UCM6510

Brands by name

Popular brands