Grandstream Networks UCM6510 User Manual Download Page 270

Page: 270 / 483

P a g e

269

UCM6510 IP PBX User Manual

Version 1.0.20.31

Note

: Up to 5 welcome prompts can be used..

Digit Timeout

Configure the timeout between digit entries. After the user enters a digit,

the user needs to enter the next digit within the timeout. If no digit is

detected within the timeout, the UCM6510 will consider the entries

complete. The default timeout is 3 seconds.

Response Timeout

After playing the prompts in the IVR, the UCM6510 will wait for the DTMF

entry within the timeout (in seconds). If no DTMF entry is detected within

the timeout, a timeout prompt will be played. The default setting is 10

seconds.

Response Timeout Prompt

Select the prompt message to be played when timeout occurs.

Invalid Prompt

Select the prompt message to be played when an invalid extension is

pressed.

Response Timeout Prompt

Repeats

Configure the number of times to repeat the prompt if no DTMF input is

detected. When the loop ends, it will go to the timeout destination if

configured, or hang up. The default setting is 3.

Invalid Input Prompt Repeats

Configure the number of times to repeat the prompt if the DTMF input is

invalid. When the loop ends, it will go to the invalid destination if

configured, or hang up. The default setting is 3.

Language

Select the voice prompt language to be used for this IVR. The default

setting is "Default" which is the selected voice prompt language under Web

GUI



PBX

Settings



Voice

Prompt



Language

Settings

The

dropdown list shows all the current available voice prompt languages on

the UCM6510. To add more languages in the list, please download voice

prompt package by selecting "Check Prompt List" under Web GUI



PBX

Settings



Voice Prompt



Language Settings

Key Pressing Events

Key Press Event:

Press 0

Press 1

Press 2

Press 3

Press 4

Press 5

Press 6

Press 7

Press 8

Press 9

Press *

Timeout

Select the event for each key pressing for 0-9, *, Timeout and Invalid. The

event options are:



Extension



Voicemail



Conference Rooms



Voicemail Group



IVR



Ring Group



Queues



Page Group



Fax



Custom Prompt



Hangup

Summary of Contents for UCM6510




































































































































































































































































































































































































































































































Search results

Summary of Contents for UCM6510

Reviews:

Related manuals for UCM6510

Brands by name

Popular brands

Grandstream Networks UCM6510, User Manual

Search results

Summary of Contents for UCM6510

Reviews:

Related manuals for UCM6510

Brands by name

Popular brands