Grandstream Networks UCM6510 User Manual Download Page 120

Page: 120 / 483

P a g e

119

UCM6510 IP PBX User Manual

Version 1.0.20.31

Server Path

When URL is selected as firmware source, configure the firmware

upgrading server path.

File Prefix

When URL is selected as firmware source, configure the firmware file

prefix. If configured, only the firmware with the matching encrypted prefix

will be downloaded and flashed into the phone, if URL is selected as

firmware source.

File Postfix

When URL is selected as firmware source, configure the firmware file

postfix. If configured, only the configuration file with the matching encrypted

postfix will be downloaded and flashed into the phone.

Allow DHCP Option 43/66

If DHCP option 43 or 66 is enabled on the LAN side, the TFTP server can

be redirected.

Automatic Upgrade

If enabled, the end point device will automatically upgrade if a new firmware

is detected. Users can select automatic upgrading by day, by week or by

minute.



By week

Once selected, specify the day of the week to check HTTP/TFTP

server for firmware upgrades or configuration files changes.



By day

Once selected, specify the hour of the day to check the HTTP/TFTP

server for firmware upgrades or configuration files changes.



By minute

Once selected, specify the interval

that the SIP end device will

request for new firmware every

minutes.

Firmware Upgrade Rule

Specifies how firmware upgrade and provision requests will be sent.

Web Access

Admin Password

Configure the administrator password for admin level login.

End-User Password

Configure the end-user password for the end user level login.

Web Access Mode

Select HTTP or HTTPS as the web access protocol.

Web Server Port

Configure the port for web access. The valid range is 1 to 65535.

Security

Disable Telnet/SSH

Enable Telnet/SSH access for the SIP end device. If the SIP end device

supports Telnet access, this option controls the Telnet access of the device;

if the SIP end device supports SSH access, this option controls the SSH

access of the device.

Syslog

Syslog Server

Configure the URL/IP address for the syslog server.

Syslog Level

Select the level of logging for syslog.

Send SIP Log

Configures whether SIP messages will be included in the syslog.

Summary of Contents for UCM6510




































































































































































































































































































































































































































































































Search results

Summary of Contents for UCM6510

Reviews:

Related manuals for UCM6510

Brands by name

Popular brands

Grandstream Networks UCM6510, User Manual

Search results

Summary of Contents for UCM6510

Reviews:

Related manuals for UCM6510

Brands by name

Popular brands