Grandstream Networks UCM6510 User Manual Download Page 384

Page: 384 / 483

P a g e

383

UCM6510 IP PBX User Manual

Version 1.0.20.31

SIP Settings/TOS

Table 122: SIP Settings/ToS

ToS For SIP

Configure the Type of Service for SIP packets. The default setting is None.

ToS For RTP Audio

Configure the Type of Service for RTP audio packets. The default setting is

None.

ToS For RTP Video

Configure the Type of Service for RTP video packets. The default setting is

None.

Default Incoming/Outgoing

Registration Time

Configure the default duration (in seconds) of incoming/outgoing

registration. The default setting is 120.

Max

Registration/Subscription

Time

Configure the maximum allowed duration (in seconds) of incoming

registration and subscription requests. Default value is 3600.

Min

Registration/Subscription

Time

Configure the minimum allowed duration (in seconds) of incoming

registration and subscription requests. Default value is 60.

Enable Relaxed DTMF

Select to enable relaxed DTMF handling. This may cause audio to be

mistaken for DTMF The default setting is "No".

DTMF Mode

Select DTMF mode to send DTMF. The default setting is RFC4733. If "Info"

is selected, SIP INFO message will be used. If "Inband" is selected, 64-kbit

codec PCMU and PCMA are required. When "Auto" is selected, "RFC4733"

will be used if offered. Otherwise "Inband" will be used. The default setting

is "RFC4733".

RTP Timeout

During an active call, if there is no RTP activity before the configured

timeout, the call will be terminated. The default setting is no timeout.

Note:

This setting does not apply to calls on hold.

RTP Hold Timeout

When the call is on hold, if there is no RTP activity before the configured

timeout, the call will be terminated. This value of RTP Hold Timeout should

be larger than RTP Timeout.

The default setting is no timeout.

RTP Keep-alive

This feature can be used to avoid abnormal call drop when the remote

provider requires RTP traffic during proceeding.

For example, when the call goes into voicemail and there is no RTP traffic

sent out from UCM, configuring this option can avoid voicemail drop.

When configured, RTP keep-alive packet will be sent to remote party at the

configured interval. If set to 0, RTP keep-alive is disabled.

100rel

Configure the 100rel setting on UCM6510.
The default setting is “Yes”.

Trust Remote Party ID

Configure whether the Remote-Party-ID should be trusted. The default

Summary of Contents for UCM6510




































































































































































































































































































































































































































































































Search results

Summary of Contents for UCM6510

Reviews:

Related manuals for UCM6510

Brands by name

Popular brands

Grandstream Networks UCM6510, User Manual

Search results

Summary of Contents for UCM6510

Reviews:

Related manuals for UCM6510

Brands by name

Popular brands