Grandstream Networks UCM6510 User Manual Download Page 357

Page: 357 / 483

P a g e

356

UCM6510 IP PBX User Manual

Version 1.0.20.31

Call Forward Unconditional

Activate



Default Code:

*72



Enter the code and follow the voice prompt. Or enter the code

followed by the extension to forward the call.

Call Forward Unconditional

Deactivate



Default Code:

*73

Remote Call Forward Enable



If enabled, this option will allow specific extensions to dial the

remote call forwarding feature codes to set call forwarding for

any extension.

Remote Call Forward Busy

Enable



Default Code:

*65



Enter the code and follow the voice prompt to set the remote

extension number where you want to enable Call Forward Busy

and the target destination.

Remote Call Forward Busy

Disable



Default Code:

*651



Enter the code and follow the voice prompt to set the remote

extension number where you want to disable the Call Forward

Busy.

Remote Call Forward No Answer

Enable



Default Code:

*66



Enter the code and follow the voice prompt to set the remote

extension number where you want to enable Call Forward No

Answer and the target destination.

Remote Call Forward No Answer

Disable



Default Code:

*661



Enter the code and follow the voice prompt to set the remote

extension number where you want to disable the Call Forward

No Answer.

Remote Call Forward

Unconditional Enable



Default Code:

*67



Enter the code and follow the voice prompt to set the remote

extension number where you want to enable Call Forward

Unconditional and the target destination.

Remote Call Forward

Unconditional Disable



Default Code:

*671



Enter the code and follow the voice prompt to set the remote

extension number where you want to disable the Call Forward

Unconditional.

Remote Call Forward Whitelist

Only the Extensions selected in this whitelist can configure call

forwarding for any extension via feature codes.

Feature Codes

Voicemail Access Code



Default Code:

*98



Enter *98 and follow the voice prompt. Alternatively, dial *98

followed by the extension and pound (#) to immediately access

the entered extension's voicemail box.

Summary of Contents for UCM6510




































































































































































































































































































































































































































































































Search results

Summary of Contents for UCM6510

Reviews:

Related manuals for UCM6510

Brands by name

Popular brands

Grandstream Networks UCM6510, User Manual

Search results

Summary of Contents for UCM6510

Reviews:

Related manuals for UCM6510

Brands by name

Popular brands