manualshive.com logo in svg

Grandstream Networks UCM6510, User Manual

The Grandstream Networks UCM6510 offers advanced VoIP communication solutions for businesses. Harness the power of this feature-packed device by unlocking its full potential with the user manual. Download the manual for free at manualshive.com and discover how to optimize your communication experience with this innovative product.

Share
Download
background image

 

P a g e

 | 

370 

 

UCM6510 IP PBX User Manual 

Version 1.0.20.31 

PBX SETTINGS 

 

This section describes internal options that have not been mentioned in previous sections yet. The settings 

in this section can be applied globally to the UCM6510, including general configurations, jitter buffer, RTP 

settings,  hardware  config  and  STUN  monitor.  The  options  can  be  accessed  via  Web  GUI

PBX 

Settings

General Settings.

 

General Settings 

Table 109: PBX Settings/General

 

General Preferences

 

Global Outbound CID 

Configure  the  global  CallerID  used  for  all  outbound  calls  when  no  other 

CallerID is defined with higher priority. If no CallerID is defined for extension 

or trunk, the global outbound CID will be used as CallerID. 

Global Outbound CID Name 

Configure  the  global  CallerID  Name  used  for  all  outbound  calls.  If 

configured, all outbound calls will have the CallerID Name set to this name. 

If not, the extension's CallerID Name will be used. 

Ring Timeout 

Configure the number of seconds to ring an extension before the call goes 

to the user's voicemail box. The default setting is 60.   

Note:

 

This is the global value used for each extension if "Ring Timeout" field is left 

empty on the extension configuration page.     

Call Duration Limit 

Configure the maximum duration of call-blocking. 

Record Prompt 

If  enabled,  users  will  hear  voice  prompt  before  recording  is  started  or 

stopped.  For  example,  before  recording,  the  UCM6510  will  play  voice 

prompt "The call will be recorded". The default setting is "No". 

Enable 486 to Failover Trunk 

Reroutes  failed  outbound  calls  that  receive  a  486  response  through  the 

failover trunk to retry the call. If disabled, calls that receive a 486 response 

will be terminated. 

Device Name 

Enter a name to identify the UCM. The name will be displayed on UCM web 

interface. 

International Call Prefix 

Configure the International prefix. Default is 00. 

If empty, international call prefix can be empty or +. 

This parameter helps the UCM to identify the international call prefix for the 
country  (00,  011,  810…)  to  avoid  any  conflict  when  using  blacklist  for 

specific countries.   

When  outbound  blacklist  is  enabled,  UCM  will  apply  the  following  rule 

Summary of Contents for UCM6510




































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for UCM6510

National Instruments Module NI PXI-8250 User Manual preview
Module NI PXI-8250
Brand: National Instruments Pages: 39
mikroElektronika CAN SPI click Quick Start Manual preview
CAN SPI click
Brand: mikroElektronika Pages: 3
Delta Electronics DTE-20T Instruction Sheet preview
DTE-20T
Brand: Delta Electronics Pages: 1
TRENDnet TW-100 Specifications preview
TW-100
Brand: TRENDnet Pages: 2
Weidmuller IE-SW-VL16-14TX-2SC Hardware Installation Manual preview
IE-SW-VL16-14TX-2SC
Brand: Weidmuller Pages: 17
NA DigiNet 416 User Manual preview
DigiNet 416
Brand: NA Pages: 22
AOpen 4-Port 10/100Mbps Ethernet Broadband Router User Manual preview
4-Port 10/100Mbps Ethernet Broadband Router
Brand: AOpen Pages: 41
Telit Wireless Solutions HE922-3GR Hardware User'S Manual preview
HE922-3GR
Brand: Telit Wireless Solutions Pages: 113
TP-Link TL-MR3220 Quick Installation Manual preview
TL-MR3220
Brand: TP-Link Pages: 87
Cypress Semiconductor CY7C68033 Specification Sheet preview
CY7C68033
Brand: Cypress Semiconductor Pages: 33
IndigoVision Compact NVR-AS 4000 User Manual preview
Compact NVR-AS 4000
Brand: IndigoVision Pages: 38
IEI Technology Mustang-M2AE-MX1 User Manual preview
Mustang-M2AE-MX1
Brand: IEI Technology Pages: 58
Comet Labs 24-Port 1000BASE-T User Manual preview
24-Port 1000BASE-T
Brand: Comet Labs Pages: 44
KYLAND Technology KIEN3016A Hardware Installation Manual preview
KIEN3016A
Brand: KYLAND Technology Pages: 19
Korenix JetNet 5720G-8P Series Quick Installation Manual preview
JetNet 5720G-8P Series
Brand: Korenix Pages: 52
NEC N8154-25 User Manual preview
N8154-25
Brand: NEC Pages: 47
Renesas H8S/2615 Series User Manual preview
H8S/2615 Series
Brand: Renesas Pages: 28
Patterson Homecraft Rolyan AA6240 Instruction Sheet preview
Homecraft Rolyan AA6240
Brand: Patterson Pages: 2

Brands by name

Popular brands

Load more brands