GE Vivid S70 User Manual Download Page 591

Page: 591 / 709

Archive

Vivid S70 / S60

–

User Manual

12-71

BC092760-1EN

XML Export configuration

The destination for transfer of patient records to XML format
must be configured prior to use. See ‘Transferring patient
records/examinations’ on

page 10-41

for a description of the

transfer function.

To configure the Transfer function:

1. Press

Utility

Config

on the Touch panel and log on as

administrator.

2. Select the

Connectivity

category and

Dataflow

subgroup.

The

Dataflow

sheet is displayed (Figure 12-53).

3. Select the dataflow

Export to XML

Figure 12-53. The Dataflow sheet (Export to XML)

Transfer to XML format - configuration

1. Select the

XML Export Service

and press

Properties

The properties window is displayed.

Figure 12-54. The XML Export Service properties window

Summary of Contents for Vivid S70





































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Vivid S70

Reviews:

Related manuals for Vivid S70

Brands by name

Popular brands

GE Vivid S70, User Manual

Search results

Summary of Contents for Vivid S70

Reviews:

Related manuals for Vivid S70

Brands by name

Popular brands