GE Vivid S70 User Manual Download Page 574

Page: 574 / 709

Customize Configuration

12-54

Vivid S70 / S60

–

User Manual

BC092760-1EN

Wireless Network Configuration

The following procedure is used to configure the Ultrasound
System for a wireless network environment. This procedure is
required for

every

new wireless network.

NOTE:

Do not use any type of wireless network adaptor other than a
GE-approved adaptor.

NOTE:

If you have questions regarding the configuration, please
contact your local IT expert.

Configuring the Wireless Network Adaptor

Follow this procedure to configure the Wireless Network
Adaptor:

1. From the default scanner screen, press

CONFIG (F2)

and

log on as

Adm

2. Select

CONNECTIVITY

(lower part of window).

3. Select the

TCP/IP

tab.

Figure 12-37. Connectivity - TCPIP Tab

Summary of Contents for Vivid S70





































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Vivid S70

Reviews:

Related manuals for Vivid S70

Brands by name

Popular brands

GE Vivid S70, User Manual

Search results

Summary of Contents for Vivid S70

Reviews:

Related manuals for Vivid S70

Brands by name

Popular brands