manualshive.com logo in svg

GE Vivid S70, User Manual


Share
Download
background image

Customize Configuration

12-60

Vivid S70 / S60

 – 

User Manual

BC092760-1EN

 

01

Data Streaming

NOTE: 

Data streaming is for informational purposes only and not 
intended for diagnostic use.

NOTE: The 

StreamServer

 option key should be installed to enable 

streaming live ultrasound data.

The system has the capability to stream live ultrasound image 
data (both 2D and 3D) over the network connection to enabled 
devices. To configure this capability perform the following steps:

Enable data streaming

1.  Press 

More

 on the control panel, then 

Utility

2.  Press 

Config…

 on the control panel

3.  Select the tab 

Connectivity

, then 

TCP/IP

4.  Press the button 

Data Streaming Settings

5.  Check 

Enable Streaming

 on the 

Data Streaming Settings

 

dialog

6.  Enter stream server 

Port No

 (or use the default port)

User setup for data streaming

Only a member of the group “ConsultingPhys” will have 
permission to receive streamed data.

See example of users who can receive streaming data below.

Summary of Contents for Vivid S70






































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Vivid S70

JB Systems INFERNO Operation Manual preview
INFERNO
Brand: JB Systems Pages: 12
Olsen Sprint Quick Operation Manual preview
Sprint
Brand: Olsen Pages: 4
Falcon Dominator Series User, Installation And Servicing Instructions preview
Dominator Series
Brand: Falcon Pages: 31
Fakir HYPO CLEAN Fast User Manual preview
HYPO CLEAN
Brand: Fakir Pages: 22
Qtx SURGE User Manual preview
SURGE
Brand: Qtx Pages: 6
GCE Zen-O lite RS-00600 User Manual preview
Zen-O lite RS-00600
Brand: GCE Pages: 20
Harris 9250-05 Operator'S Manual preview
9250-05
Brand: Harris Pages: 21
ZAMST EK-1 Instructions For Use Manual preview
EK-1
Brand: ZAMST Pages: 14
Future Artist MIDI LOOPER Manual preview
MIDI LOOPER
Brand: Future Artist Pages: 42
EHEIM classic 4200130 Operating Manual preview
4200130
Brand: EHEIM classic Pages: 128
Oscartielle MINOR 2000 G.E. Instruction Manual preview
MINOR 2000 G.E.
Brand: Oscartielle Pages: 44
Boss Audio Systems MR637U (Spanish) Manual De Usuario preview
MR637U
Brand: Boss Audio Systems Pages: 7
Waters SYNAPT G2 Operator'S, Overview And Maintenance Manual preview
SYNAPT G2
Brand: Waters Pages: 236
NightBalance NB-SPT-PX Quick Manual preview
NB-SPT-PX
Brand: NightBalance Pages: 1
Sygonix 2335667 Operating Instructions preview
2335667
Brand: Sygonix Pages: 4
Star Trac CrossTrainer Service Manual preview
CrossTrainer
Brand: Star Trac Pages: 3
Shofu Sublite V Instructions For Use Manual preview
Sublite V
Brand: Shofu Pages: 6
Darwin Fitness FB80 Assembly And Operating Instructions Manual preview
FB80
Brand: Darwin Fitness Pages: 32

Brands by name

Popular brands

Load more brands