manualshive.com logo in svg

GE Vivid S70, User Manual


Share
Download
background image

4D/Multi-plane LV

Vivid S70 / S60

 – 

User Manual

8-59

BC092760-1EN

 

01

 Figure 8-30. The Volume waveform screen

Approval

1.  Press 

Approve & Exit

 to store the measurements shown in 

the 

Measurement result

 table.

The measurements are transferred to the Worksheet.
To exit without approving, press 

Cancel

.

NOTE: 

Measurements that are not approved will not be saved.

Calculation formula and measurement accuracy

Refer to the Reference manual for calculation formula 
information and ‘Measurement accuracy’ on 

page 8-97

 for 

measurement accuracy information.

CAUTION

The measurement should not be approved if a significant part 
(more than 25%) of the left ventricular wall or the detected 
contours are outside the ultrasound sector.

Summary of Contents for Vivid S70






































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Vivid S70

ZOLL R Series In-Service Manual preview
R Series
Brand: ZOLL Pages: 5
Accu-Chek Compact Pocket User Manual preview
Compact
Brand: Accu-Chek Pages: 3
iBin Compact Installation Instructions preview
Compact
Brand: iBin Pages: 2
BACtrack ELEMENT Product Manual preview
ELEMENT
Brand: BACtrack Pages: 16
Eaton SPD Series Instruction Booklet preview
SPD Series
Brand: Eaton Pages: 16
Eaton 2596 Installation, Operation & Maintenance Manual preview
2596
Brand: Eaton Pages: 15
Quivogne SCD Operating, Maintenance & Spare Parts Book preview
SCD
Brand: Quivogne Pages: 13
laerdal SimPad Quick Start Manual preview
SimPad
Brand: laerdal Pages: 9
Ultraflex A98 Installation And Maintenance Manual preview
A98
Brand: Ultraflex Pages: 52
Palmgren 80421 Operating Manual & Parts List preview
80421
Brand: Palmgren Pages: 12
Bartscher 500830 Instructions Manual preview
500830
Brand: Bartscher Pages: 20
RAB HAZL34-40 Instructions preview
HAZL34-40
Brand: RAB Pages: 4
EditorsKeys Portable Vocal Booth Pro Studio Series Instruction Sheet preview
Portable Vocal Booth Pro Studio Series
Brand: EditorsKeys Pages: 2
Lightolier Calculite C6P38MHA Specification preview
Calculite C6P38MHA
Brand: Lightolier Pages: 2
Atlas Copco PDR 30 T Safety And Operating Instructions Manual preview
PDR 30 T
Brand: Atlas Copco Pages: 10
Agilent Technologies G1313A Reference Manual preview
G1313A
Brand: Agilent Technologies Pages: 292
illumina cBot System Manual preview
cBot
Brand: illumina Pages: 90
Westlab 664-315 Product Manual preview
664-315
Brand: Westlab Pages: 8

Brands by name

Popular brands

Load more brands